split_util: rename usbIsActive to usb_bus_detected
This follows the style rules and better reflects the intent.
Signed-off-by: Stefan Kerkmann <karlk90@pm.me>
* Move SPLIT_HAND_PIN setup to split_pre_init
* doppelganger should use old behaviour
* Add comment for future
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Make solo half of split keyboards (more) usable.
Using only one half of a split keyboard (that's using the split_common
framework to communicate) is not a great experience, since several read
timeouts per scan cycle cause an unusably slow scan rate.
This change blocks all split communication attempts for 500 ms
(configurable) after an error occurs, causing the scan rate to become at
least _more_ usable, but might need some tweaking to work fully on most
keyboards. One read timeout still needs to occur after the 500 ms has
passed, and if that timeout isn't low enough, some scan cycles may still
be too slow.
* Fix lint complaint.
* Require 25 consecutive comm errors to see comms as disconnected.
The number of max errors can be overridden by defining
`SPLIT_MAX_CONNECTION_ERRORS`.
* Add comments to new defines, and ability to disable disconnection check.
Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible
by most relevant numbers for the description.
* Make lint happy ...again
* Only update `connection_check_timer` when needed.
* Add new defines to split keyboard documentation.
* Move connection timeout logic to transport.c, add `is_transport_connected`.
* Use split_common disconnection logic in matrix.c.
Instead of doing more or less the same thing twice.
* Move disconnection logic to `transport_master`.
Is a cleaner implementation, and causes the scan rate while disconnected
to increase instead of decrease.
* Lint fixes.
* Lower default `SERIAL_USART_TIMEOUT` to 20 ms.
The read timeout must be low enough to not cause exessively long scan
cycles when using a solo split half. 10 ms was determined from testing
to work fine even with the slowest defined baudrate of 19200 (5 ms was
too low for that case), so 20 ms should be fine for most cases.
* Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h
Was somewhat mistakenly included in an earlier PR.
* Fix building with `USE_I2C`.
* Reduce built firmware size.
Not really sure why this works, the idea was taken from tzarc's work on
split disconnection.
* Tweak and improve opt-out for split disconnection logic.
There are now two ways to opt out from this feature:
* Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable
the connection status checks (also affects the slave matrix reset logic in
matrix.c, though).
* Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the
communication throttling while disconnected. Will make the firmware
smaller.
* Make split disconnection logic work with custom transports.
Includes a fallback implementation for keyboards using a custom
split_util.c but not a custom matrix.c (currently no such keyboard seems
to be merged, though).
* Remove unnecessary include of timer.h
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* added support for inverting the hand pin for split keyboards
* Added docs about SPLIT_HAND_LOW_IS_LEFT
* Update docs/feature_split_keyboard.md
bring #define for split hand pin low for left half name in line with grid pin define
Co-authored-by: Joel Challis <git@zvecr.com>
* Update quantum/split_common/split_util.c
update split hand pin low is left name to match split hand grid define
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Fixed slave-side keyboard half unresponsiveness
due to how LUFA handles USB_Disable()
* changes to formatting
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Avoid NO_USB_STARTUP_CHECK - Disable USB as checks seem to enable it somehow
* Update quantum/split_common/split_util.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Also remove NO_USB_STARTUP_CHECK from vitamins_included/rev1
* Add support for wiring RGB LEDs for both halves directly to their respective controllers
RGB LEDs for each half don't need to be chained together across the TRRS cable with this
* Add split RGB LED support for serial
* Update config/rules for bakingpy layout
* Un-nest ifdefs for hand detection
* Read RGB config state from memory instead of EEPROM for serial updates
* Reuse existing LED pointer instead of creating new one
* Eliminate separate slave loop
Both master and slave run the standard keyboard_task main loop now.
* Refactor i2c/serial specific code
Simplify some of the preprocessor mess by using common function names.
* Fix missing #endif
* Move direct pin mapping support from miniaxe to split_common
For boards with more pins than sense--sorry, switches.
* Reordering and reformatting only
* Don't run matrix_scan_quantum on slave side
* Clean up the offset/slaveOffset calculations
* Cut undebounced matrix size in half
* Refactor debouncing
* Minor fixups
* Split split_common transport and debounce code into their own files
Can now be replaced with custom versions per keyboard using
CUSTOM_TRANSPORT = yes and CUSTOM_DEBOUNCE = yes
* Refactor debounce for non-split keyboards too
* Update handwired/xealous to build using new split_common
* Fix debounce breaking basic test
* Dodgy method to allow a split kb to only include one of i2c/serial
SPLIT_TRANSPORT = serial or SPLIT_TRANSPORT = i2c will include only
that driver code in the binary.
SPLIT_TRANSPORT = custom (or anything else) will include neither, the
keyboard must supply it's own code
if SPLIT_TRANSPORT is not defined then the original behaviour (include
both avr i2c and serial code) is maintained.
This could be better but it would require explicitly updating all the
existing split keyboards.
* Enable LTO to get lets_split/sockets under the line
* Add docs for SPLIT_TRANSPORT, CUSTOM_MATRIX, CUSTOM_DEBOUNCE
* Remove avr-specific sei() from split matrix_setup
Not needed now that slave doesn't have a separate main loop.
Both sides (on avr) call sei() in lufa's main() after exiting
keyboard_setup().
* Fix QUANTUM_LIB_SRC references and simplify SPLIT_TRANSPORT.
* Add comments and fix formatting.
* Add provisional Helix implementation to test the quantum/split_common.
* copy keyboards/helix/serial.[ch] to quantum/split_common/
* Make serial.c a pure driver.
Remove buffer name and buffer size from serial.c. They should be placed in the caller(matrix.c, split_utils.c).
* remove quantum/split_common/serial_backward_compatibility.h
* Changed array serial_master_buffer to structure serial_m2s_buffer.
* Changed array serial_slave_buffer to structure serial_s2m_buffer.
* Change keyboards/miniaxe/matrix.c
I also made changes to quantum/split_comon/matrix.c to keyboards/miniaxe/matrix.c.
Note: I contacted @ka2hiro, creator of miniaxe, and I got permission to change keyboards/miniaxe/matrix.c.
* update history comment in quantum/split_common/serial.c
* Revert "Add provisional Helix implementation to test the quantum/split_common."
This reverts commit 168c82ef82c88e79979d9796bab9cc819cc2f685.
* fix keyboards/miniaxe/matrix.c, quantum/split_common/matrix.c
avr-gcc 4.9.[23] report error.
avr-gcc 5.4.0, avr-gcc 7.3.0 pass.
It is funny.
* update comment quantum/split_common/serial.c
* Reserve RGBLIGHT_SPLIT macro in quantum/split_common
Added JTAG disable code to the split_common slave code since the slave never calls keyboard_init(). In the future the slave should likely be modified to call keyboard_init() in some way, but without calling any of the unnecessary USB initialization code.
