1
0
Fork 0

Bringing Massdrop keyboard hardware configuration to keyboard level (#4593)

MCU Pins for debugging, LED, boot tracing, and shift registers are now configurable at keyboard level.
Macros led_* replaced by DBG_LED_*
Macros m15_* replaced by DBG_1_*
Macros m27_* replaced by DBG_2_*
Macros m28_* replaced by DBG_3_*
For CTRL and ALT keyboards, debug boot tracing pin default now set to pad M27 instead of M28 since although M28 is not being used, it is technically a signal for USB port detection.
m15_print(...) renamed to dbg_print(...) to get away from hard coded port names.
dbg_print function now follows similar pattern to debug led output.
This commit is contained in:
patrickmt 2018-12-10 14:28:06 -05:00 committed by Drashna Jaelre
parent e99615b2ac
commit 4a5e68f4f2
12 changed files with 374 additions and 185 deletions

View file

@ -32,17 +32,64 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define MATRIX_ROWS 11
#define MATRIX_COLS 8
/* MCU Port name definitions */
#define PA 0
#define PB 1
/* Port and Pin definition of key row hardware configuration */
#define MATRIX_ROW_PORTS PB, PB, PB, PB, PB, PB, PA, PA, PB, PB, PB
#define MATRIX_ROW_PINS 4, 5, 6, 7, 8, 9, 10, 11, 10, 11, 12
/* Port and Pin definition of key column hardware configuration */
#define MATRIX_COL_PORTS PA, PA, PA, PA, PA, PA, PA, PA
#define MATRIX_COL_PINS 0, 1, 2, 3, 4, 5, 6, 7
/* Print boot debug codes using debug LED when M28 and M30 shorted */
#define DEBUG_BOOT_TRACING
/* This Shift Register expands available hardware output lines to control additional peripherals */
/* It uses four lines from the MCU to provide 16 output lines */
/* Shift Register Clock configuration (MCU to ShiftRegister.RCLK) */
#define SR_EXP_RCLK_PORT PB
#define SR_EXP_RCLK_PIN 14
/* Shift Register Output Enable configuration (MCU to ShiftRegister.OE_N) */
#define SR_EXP_OE_N_PORT PB
#define SR_EXP_OE_N_PIN 15
/* SERCOM port to use for Shift Register SPI */
/* DATAOUT and SCLK must be configured to use hardware pins of this port */
#define SR_EXP_SERCOM SERCOM2
/* Shift Register SPI Data Out configuration (MCU.SERCOMx.PAD[0] to ShiftRegister.SER) */
#define SR_EXP_DATAOUT_PORT PA
#define SR_EXP_DATAOUT_PIN 12
#define SR_EXP_DATAOUT_MUX 2
/* Shift Register SPI Serial Clock configuration (MCU.SERCOMx.PAD[1] to ShiftRegister.SRCLK) */
#define SR_EXP_SCLK_PORT PA
#define SR_EXP_SCLK_PIN 13
#define SR_EXP_SCLK_MUX 2
/* Debug LED (Small LED Located near MCU) */
#define DEBUG_LED_ENABLE 1
#define DEBUG_LED_PORT PA
#define DEBUG_LED_PIN 27
/* Additional debugging ports */
/* PCB M21 */
#define DEBUG_PORT1_ENABLE 1
#define DEBUG_PORT1_PORT PB
#define DEBUG_PORT1_PIN 3
/* PCB M23 */
#define DEBUG_PORT2_ENABLE 1
#define DEBUG_PORT2_PORT PB
#define DEBUG_PORT2_PIN 17
/* PCB M25 */
#define DEBUG_PORT3_ENABLE 1
#define DEBUG_PORT3_PORT PA
#define DEBUG_PORT3_PIN 20
/* Debug Boot Tracing - During boot sequence, ground this pin to halt and display debug code using Debug LED */
/* This is useful in determining which hardware device may have malfunctioned or is improperly configured */
/* Feature is automatically disabled after successful boot */
/* PCB M27 */
#define DEBUG_BOOT_TRACING_ENABLE 1
#define DEBUG_BOOT_TRACING_PORT PB
#define DEBUG_BOOT_TRACING_PIN 23
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCING_DELAY 5

View file

@ -75,7 +75,7 @@ void matrix_init(void)
PORT->Group[col_ports[col]].DIRSET.reg = 1 << col_pins[col]; //Output
PORT->Group[col_ports[col]].OUTCLR.reg = 1 << col_pins[col]; //Low
}
matrix_init_quantum();
}
@ -91,7 +91,7 @@ uint8_t matrix_scan(void)
if (CLK_get_ms() < mdebouncing) return 1; //mdebouncing == 0 when no debouncing active
//m15_off; //Profiling scans
//DBG_1_OFF; //Profiling scans
memset(mlatest, 0, MATRIX_ROWS * sizeof(matrix_row_t)); //Zero the result buffer
@ -135,7 +135,7 @@ uint8_t matrix_scan(void)
mdebouncing = CLK_get_ms() + DEBOUNCING_DELAY;
}
//m15_on; //Profiling scans
//DBG_1_ON; //Profiling scans
matrix_scan_quantum();